Problem 1
When working with a solid sample, often it is necessary to bring the analyte into solution by digesting the sample with a suitable solvent. Any remaining solid impurities are removed by filtration before continuing with the analysis. In a typical total analysis method, the procedure might read After digesting the sample in a beaker using approximately \(25 \mathrm{~mL}\) of solvent, remove any solid impurities that remain by passing the solution the analyte through filter paper, collecting the filtrate in a clean Erlenmeyer flask. Rinse the beaker with several small portions of solvent, passing these rinsings through the filter paper and collecting them in the same Erlenmeyer flask. Finally, rinse the filter paper with several portions of solvent, collecting the rinsings in the same Erlenmeyer flask. For a typical concentration method, however, the procedure might state After digesting the sample in a beaker using \(25.00 \mathrm{~mL}\) of solvent, remove any solid impurities by filtering a portion of the solution containing the analyte. Collect and discard the first several \(\mathrm{mL}\) of filtrate before collecting a sample of \(5.00 \mathrm{~mL}\) for further analysis. Explain why these two procedures are different.
Problem 2
A certain concentration method works best when the analyte's concentration is approximately 10 ppb. (a) If the method requires a sample of \(0.5 \mathrm{~mL}\), about what mass of analyte is being measured? (b) If the analyte is present at \(10 \% \mathrm{w} / \mathrm{v}\), how would you prepare the sample for analysis? (c) Repeat for the case where the analyte is present at \(10 \% \mathrm{w} / \mathrm{w}\). (d) Based on your answers to parts (a)-(c), comment on the method's suitability for the determination of a major analyte.
Problem 3
An analyst needs to evaluate the potential effect of an interferent, \(I,\) on the quantitative analysis for an analyte, \(A\). She begins by measuring the signal for a sample in which the interferent is absent and the analyte is present with a concentration of 15 ppm, obtaining an average signal of 23.3 (arbitrary units). When she analyzes a sample in which the analyte is absent and the interferent is present with a concentration of \(25 \mathrm{ppm}\), she obtains an average signal of 13.7 . (a) What is the sensitivity for the analyte? (b) What is the sensitivity for the interferent? (c) What is the value of the selectivity coefficient? (d) Is the method more selective for the analyte or the interferent? (e) What is the maximum concentration of interferent relative to that of the analyte if the error in the analysis is to be less than \(1 \% ?\)
Problem 4
A sample is analyzed to determine the concentration of an analyte. Under the conditions of the analysis the sensitivity is \(17.2 \mathrm{ppm}^{-1}\). What is the analyte's concentration if \(S_{\text {total }}\) is 35.2 and \(S_{\text {reag }}\) is \(0.6 ?\)
Problem 8
Ibrahim and co-workers developed a new method for the quantitative analysis of hypoxanthine, a natural compound of some nucleic acids. As part of their study they evaluated the method's selectivity for hypoxanthine in the presence of several possible interferents, including ascorbic acid. (a) When analyzing a solution of \(1.12 \times 10^{-6} \mathrm{M}\) hypoxanthine the authors obtained a signal of \(7.45 \times 10^{-5}\) amps. What is the sensitivity for hypoxanthine? You may assume the signal has been corrected for the method blank. (b) When a solution containing \(1.12 \times 10^{-6} \mathrm{M}\) hypoxanthine and \(6.5 \times 10^{-5} \mathrm{M}\) ascorbic acid is analyzed a signal of \(4.04 \times 10^{-5}\) amps is obtained. What is the selectivity coefficient for this method? (c) Is the method more selective for hypoxanthine or for ascorbic acid? (d) What is the largest concentration of ascorbic acid that may be present if a concentration of \(1.12 \times 10^{-6} \mathrm{M}\) hypoxanthine is to be determined within \(1.0 \%\) ?
